EWS2 EWS3.2 EMULATOR support E34 E36 E38 E39 E46 IMMO Immobilizer

Rp350.000

INSTALLATION:
1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch EMULATOR CONFIGURATION UTILITY:

Description

EWS2 EWS3.2 EMULATOR support E34 E36 E38 E39 E46 IMMO Immobilizer

INSTALLATION:
1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch EMULATOR CONFIGURATION UTILITY:

3. Choose COM port, write in desired ISN number, press button Store. Or –
4. For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option “ECU xxxxx”, press Read. Software will try to read ISN. If successful, choose option “EWS emulator” and press button Store to save ISN number into emulator.
5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to DME(DDE) <-> EWS line.
6. Don’t forget to short two starter relay wires (EWS connector)!
7. Car is ready to start.

In case of EWS3.2 similar procedure is used, only difference is that that it is NOT connected directly to diagnostic K-line.
There are NO any counters or car starts limited. You can change and store new ISN without any limitations.
Emulator is shipped with JUMPER 1 shorted. For testing purposes ISN 0579 is stored by default.

Brand Name:
EWS2 EWS3.2 Emulator for bmw
Model Name :EWS2 EWS3.2 Emulator for bmw
Item Width :12 inch
Car Maker :BMW
Material Type :Plactis
Item Height :15 inch
Voltage :w
Language :English
Special Features :ecu chip tuning tool
Item Type :Car Diagnostic Cables and Connectors
Item Length :11 inch
Item Weight :0.5 kg
Product Description
For BMW EWS2 EWS3.2 Emulator E34 E36 E38 E39 E46

Installation:
1. Remove original EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch EMULATOR CONFIGURATION UTILITY:
3. Choose COM port, write in desired ISN number, press button Store. Or –
4. For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option ECU xxxxx , press Read. Software will try to read ISN. If successful, choose option EWS emulator and press button Store to save ISN number into emulator.
5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to DME(DDE) <-> EWS line.
6. Don t forget to short two starter relay wires (EWS connector)!
7. Car is ready to start.

In case of EWS3.2 similar procedure is used, only difference is that that it is NOT connected directly to diagnostic K-line.
There are NO any counters or car starts limited. You can change and store new ISN without any limitations.
Emulator is shipped with JUMPER 1 shorted. For testing purposes ISN 0579 is stored by default.

kita semua tahu bahwa permainan gim online yang dinanti akan segera hadir disitu utama kita untuk para pemain dan penikmat permainan agen sbobet terbesar dan terunik di indonesia tercinta ini

lagi pula kita harus mempersiapkan semua nya dengan matang agar kita dapat dengan mudah bermain tebak angka di agen togel yang dimana kita semua tahu itu tidak mudah untuk di cerna

Obd2 Jatim © 2018